| 1、产品介绍Product introduction
Acrylic grouting material is a kind of non-toxic and environmentally friendly grouting material with acrylic polymer as the main agent. Slurry viscosity is low, can be injected into the base of the micro cracks, solidification after the formation of a high flexibility, water can expand, impermeable elastic gel.
丙烯酸盐灌浆材料是一种以丙烯酸聚合物为主剂，无毒环保的灌浆材料。浆液粘度低，可灌入基层的细微裂缝，凝固后形成一种具有高柔韧性、遇水可膨胀、不透水的弹性凝胶体。
2、产品特点Product features
◇Low viscosity, high permeability environmental grouting material, suitable for any dense complex structure.
低粘度、高渗透性的环保型灌浆材料，适用于任何密实的复杂的结构体。
◇The low shrinkage formula with high viscosity, strength and toughness can effectively reduce the repeated seepage of foundation settlement or structure expansion.
高粘强韧性的低收缩配方，可有效降低基础沉降或结构伸缩的反复渗漏水。
3、适用范围Scope of application
◇Anti-seepage grouting for DAMS, reservoirs, etc
大坝、水库等的防渗灌浆
◇Seepage prevention and sealing of tunnel bushing
隧道的防渗堵漏和隧道衬套的密封
◇Underground building, basement, kitchen, bathroom and other seepage plug leakage
地下建筑物、地下室、厨房、厕浴间等防渗堵漏
◇Seal cracks in concrete and rock structures against seepage and leakage
封闭混凝土和岩石结构的裂缝防渗堵
4、施工要点Key points of construction
◇Check the leaking part, clean the leaking part, confirm the crack type, drill hole, install the grouting nozzle on the effective grouting hole.
检查漏水部位，清洁渗漏部位，确认裂缝种类，钻孔，在有效注浆孔上安装注浆嘴。
◇According to the proportion of materials prepared into A, B two components, the use of double liquid high-pressure grouting machine, according to the volume of 1:1 construction, grouting machine should be kept dry before construction, no dirt.
根据材料配比配制成A、B两个组分，采用双液型高压灌浆机，按照体积比1:1进行施工，灌浆机在施工前应保持干燥，无污物。
◇Starting from the first grouting nozzle from low to high, grout is injected and the pressure is gradually increased. When the grout appears in the adjacent grouting hole, it is moved to the next adjacent grout hole and the grout is continued. After all grout is finished, it is returned to the first grouting nozzle and grout again.
从第一个注浆嘴由低至高开始灌入浆液，逐步提高压力，当相邻浆孔出现浆液时，移至下一个相邻的浆孔，继续灌浆，全部灌浆结束后，回到第一个注浆嘴，再灌浆一遍。
◇72 hours after the completion of grouting, check the leakage site for water seepage. If there is no water seepage, remove the grouting nozzle and seal and smooth the base surface with epoxy mortar or quick-dry cement.
灌浆结束后72小时检查渗漏部位有无渗水，若无渗水，移除注浆嘴，用环氧砂浆或快干水泥将基面封闭、抹平。
◇After construction, immediately use cleaning agent to clean the desired equipment and tools in contact with slurry. Waste should be centralized treatment, not discarded at will.
施工结束后，立即用清洗剂清洗与浆液接触的所欲设备和工具。废弃物应集中处理，不得随意丢弃。 |
|
